chev dana 44 done right

[tavis43]

chev danad 44
all new from end to end
yukon chromo axles and super joints
dana 4.56 gear
ox locker
rev high steer reamed for chev 1 ton tie rods
extra long studs

i have alot into this and am not sure i will sell it but i have 39.5 iroks and i am not sure it will stand up to the abuse

open to offers and i have $3000 into it

[fliptuner]

post an asking price please

[pumpkin]

I have $1200 cash.

[tavis43]

i think asking will be 2500 obo

[jeepxj89]

not to **** on your parade but noones going to buy a 44 for 2500 when a d60 can be had for around 1200.

i just sold a built up brand new ford d44 and 9 inch for 1800.....

[tavis43]

ya ok good luck with that i can get a factory 60 for 300 bucks then chromo, ox, gears, setup, brakes, and bearing. of ya high steer and hubs? ok now whats the cost??

[jeepxj89]

60 shafts are a lot cheaper than d44 shafts. find a clean 60 that has 4.56 already . weld the carrier.

hi steer is about 350 for decent arms .depending what kind of draglink and tie rod you want , factor that price on.

hubs are about 200.

like i said 2500 for a d44 just aint right...

[tavis43]

big difference between rod and an ox

[Donkeyloaf]

Hey travis I will take the D60 you can get for $350? I will be in PG next week.

[pumpkin]

I'll take 5 of those $300. 60's

[tavis43]

i could get you 5
but you would have to come to pg to get them

[pumpkin]

If they are chevy d60's I might just have to make a trip for that price.

[tavis43]

if you are really into it i can get exact # on what and how meany and i am headed to salmon arm at the end of the month

[pumpkin]

For that price,,, you bet,,, let me know as I will have to arrange for the time off to get them.

[ANDYrew]

Hijack.....but anyway......What's the deal with the brand new 60s for 300, I need one, why so cheap? I don't understand?

[expotruck]

i will take a 60 as well

[whitetrashxj]

when can i come pick up my front 60???

[Mott]

Yea I will take at least 20 for 300 bucks, i got cash plus cash for you if its true, I doubt it is since i called everywhere this side of the globe and a POS d60 goes for 1200.

[Mott]

PS Bolt that thing into yourtruck and wheel it, if you have chromo shafts i doubt 39.5s will break that axle, plus they have lifetime warranty anyway.

[steve604]

60 shafts are a lot cheaper than d44 shafts. find a clean 60 that has 4.56 already . weld the carrier.

hi steer is about 350 for decent arms .depending what kind of draglink and tie rod you want , factor that price on.

hubs are about 200.

like i said 2500 for a d44 just aint right...

are you seriously comparing a welded dana 60 carrier to an ox locker?

....wow :shakehead:

if he posted a price of $2500 for the axle then that is what he is asking for it. he is not looking for your opinion on what is better and he doesn't sound like he needs a little cash for meth.

if the price is too high for you then offer what you think it's worth and move on, even a low ball offer is fine. he is obviously not going to drop the price to $1200 for you because you know how to weld spider gears to a carrier.

[copeland]

....wow :shakehead:

he doesn't sound like he needs a little cash for meth.



yea, Tavis kicked the habit a few years ago...:laugh:laugh:laugh